The Linksys MR7350 MAX-STREAM® AX1800 Dual-Band WiFi 6 Router is powered by Intelligent Mesh™ technology that adapts to your Wi-Fi needs. Your devices will always have a full-strength signal throughout your entire home.
HARDWARE INFORMATION
The Linksys MR7350 has the following parts:
Ports:
- Four Gigabit ethernet LAN ports
- One Gigabit internet WAN port
- Power port (12V, 2A)
- One USB 3.0 port to support USB drives
NOTE: The USB feature is supported only when the Linksys MR7350 is in parent mode. It is NOT supported when the Linksys MR7350 is in child mode.
- Windows®: NTFS and FAT32
- Mac®: APFS (read-only) and HFS+
- Supports Server Message Block (SMB) v2.0
- UPnP®
- Supports up to 1100mA current draw
Buttons and switch:
- Wi-Fi Protected Setup™ (WPS) button
- Reset button
- Power switch (rocker style)
The Linksys MR7350 has the following features:
- Concurrent Dual-Band
- Supports 802.11ax (AX1800) up to 1.8 Gbps
- Coverage of up to 1,700 sq ft
- 2x2 simultaneous data streams for stronger, faster performance
- Intelligent Mesh technology
- Beamforming technology
- Guest network
- Parental Controls
- Supports parent/child mode
- Wi-Fi Protected Setup (WPS)
The warranty period is dependent on the country of purchase. Learn more.
The lights indicate the different statuses and activities of your router.
The Linksys MR7350 has one USB 3.0 port for a USB storage device. However, virtual printing is not supported.
The Linksys MR7350 has a 1.2 GHz quad-core processor.
The Linksys MR7350 has the following default settings:
- The default IP address is 192.168.1.1.
- The default Guest network IP address range is 192.168.3.x.
NOTE: If the upstream device uses the same IP address, the router will automatically use a different LAN IP address to avoid any conflict.
- The default administrator password of an unconfigured router is admin.
- The default Wi-Fi name is _LinksysSetupxxx (where xxx represents the last three digits of the router's MAC address).
- Each router has a unique pre-assigned Wi-Fi password (found at the bottom of the router).
- The default Guest Wi-Fi name is _LinksysSetupxxx-guest (where xxx represents the last three digits of the router’s MAC address).
- The Guest network is turned OFF by default. It can be enabled using the router's web interface.
SETUP AND INSTALLATION
You will need the following for setup:
- Active internet connection
- A computer with the latest desktop browser to manage router settings - Google Chrome™, Microsoft Edge™, Firefox®, or Safari®
You can set up your Linksys MR7350 using the web interface or using the 5-Button push method.
You can add child nodes using the following methods:
• 5-Button Push method
• CA Router Setup tab
The Linksys MR7350 supports the following Wi-Fi security modes:
- WPA2™/WPA3™ Mixed Personal
- WPA3 Personal Only
- WPA2 Personal
- Open
FIRMWARE UPGRADE
By default, your router's Automatic Firmware Update feature is enabled and will upgrade the firmware whenever a new version is released. If you turn OFF Automatic Firmware Update, you will have to click the Check for Updates button to check if a new firmware is available before you can upgrade your device.
The firmware version can be found on the router's web interface. To access it, go to Connectivity > Basic tab and then look for Current Version.
TROUBLESHOOTING
The External Storage feature of the Linksys MR7350 allows you to connect an external storage device to its USB port to share an entire hard drive. It features one USB 3.0 port for a storage drive.
The Linksys MR7350 supports the following file formats:
- For Windows: NTFS and FAT32
- For Mac: APFS (read-only) and HFS+
No. The USB port doesn't support FTP.
Yes. This can be done by enabling Authentication through your router's External Storage feature.
NOTE: The username should have a minimum of four and a maximum of 12 alphanumeric characters, while the password should have a minimum of four and a maximum of 50 alphanumeric characters. Both can include valid characters such as an underscore ( _ ) or a dash ( – ). To learn more about the External Storage feature of the Linksys MR7350, click here.
You can recover your admin password using the five-digit recovery code printed on the product label at the bottom. Follow the steps below to learn how:
1. Connect a computer or laptop to your Linksys WiFi.
2. Open a web browser to access your router's web interface.
3. Click Reset Password.
4. Enter the Recovery Key found on the bottom of the router, then select Submit.
5. Create a new password and hint, then click Reset. This will only reset your password, not your router settings. Make sure to write down your new password, as it is case-sensitive.
6. Wait until settings have been applied. After that, you can access the router using the new password you created.
To locate the exact model number of your router, check its product label located at the bottom. The web interface will display your model series, but the product label contains the exact model number.
For the Linksys mesh router to work with a 5G router, your ISP must provide a 5G router with an ethernet port for connection to the parent node.
Yes. It supports IPv6.
